2478 omni nuvo lithium ep no. 2 grease (english (us)) citgo msds

OMNI Nuvo Lithium EP No. 2
Material Safety Data Sheet
CITGO Petroleum Corporation
P.O. Box 3758
Hazard Rankings
Tulsa, OK 74102-3758
Revision Date
HMIS NFPA
IMPORTANT: Read this MSDS before handling or disposing of this product and pass this
Health Hazard
information on to employees, customers and users of this product.
Fire Hazard
Emergency Overview
Reactivity
Physical State Semi-solid to solid (Smooth texture)
* = Chronic Health Hazard
WARNING:
Protective Equipment
Injection under the skin can cause severe injury.
Most damage occurs in the first few hours.

Minimum Recommended
See Section 8 for Details
Initial symptoms may be minimal.
Hot grease will cause thermal burns upon contact.

Spills may create a slipping hazard.
SECTION 1. PRODUCT IDENTIFICATION
Trade Name
Technical Contact
Product Number
Medical Emergency
CAS Number
CHEMTREC Emergency
(United States Only)
Product Family
Synonyms
Lubricating grease;CITGO® Material Code No.: 665608229 SECTION 2. COMPOSITION
Component Name(s)
CAS Registry No.
Concentration (%)
Distillates, petroleum, hydrotreated heavy naphthenic Residual oils, petroleum, solvent-refined Distillates, petroleum, hydrotreated light naphthenic OMNI Nuvo Lithium EP No. 2 Grease
SECTION 3. HAZARDS IDENTIFICATION
Also see Emergency Overview and Hazard Ratings on the top of Page 1 of this MSDS.
Major Route(s) of Entry Skin contact.
Signs and Symptoms of Acute Exposure
Inhalation
No significant adverse health effects are expected to occur upon short-term exposure atambient temperatures. At elevated temperatures, product vapor may cause respiratory tractirritation. Repeated or prolonged overexposure to product mists can result in respiratory tractinflammation and an increased risk of infection.
Eye Contact
This material can cause mild eye irritation from contact with product or product mists.
Skin Contact
This material can cause mild skin irritation from prolonged or repeated skin contact.
Injection under the skin can cause inflammation and swelling. Injection of pressurizedhydrocarbons can cause severe, permanent tissue damage. Initial symptoms may be minor.
Injection of petroleum hydrocarbons requires immediate medical attention. Skin contact withhot material may result in severe burns.
Ingestion
This material can cause a laxative effect. If swallowed in large quantities, this material canobstruct the intestine.
Chronic Health Effects
This product contains a petroleum-based mineral oil. Prolonged or repeated skin contact can cause mild irritation and inflammation characterized by drying, cracking, (dermatitis) oroil acne. Repeated or prolonged inhalation of petroleum-based mineral oil mists atconcentrations above applicable workplace exposure levels can cause respiratory irritation orother pulmonary effects.
Conditions Aggravated
Disorders of the following organs or organ systems that may be aggravated by significant by Exposure
exposure to this material or its components include: Skin Target Organs
May cause damage to the following organs: skin.
Carcinogenic Potential
This product is not known to contain any components at concentrations above 0.1% whichare considered carcinogenic by OSHA, IARC or NTP.
OSHA Hazard Classification is indicated by an "X" in the box adjacent to the hazard title. If no "X" is present,
the product does not exhibit the hazard as defined in the OSHA Hazard Communication Standard (29 CFR
1910.1200).

OSHA Health Hazard Classification
OSHA Physical Hazard Classification
Irritant
Sensitizer
Combustible
Explosive
Pyrophoric
Highly Toxic
Flammable
Oxidizer
Water-reactive
Corrosive
Carcinogenic
Compressed Gas
Organic Peroxide
Unstable
SECTION 4. FIRST AID MEASURES
Take proper precautions to ensure your own health and safety before attempting rescue or providing first aid.
For more specific information, refer to Exposure Controls and Personal Protection in Section 8 of this MSDS.

Inhalation
Vaporization is not expected at ambient temperatures. This material is not expected to causeinhalation-related disorders under anticipated conditions of use. In case of overexposure,move the person to fresh air.
OMNI Nuvo Lithium EP No. 2 Grease
Eye Contact
Check for and remove contact lenses. Flush eyes with cool, clean, low-pressure water whileoccasionally lifting and lowering eyelids. Seek medical attention if excessive tearing, redness,or pain persists.
Skin Contact
If burned by hot material, cool skin by quenching with large amounts of cool water. Forcontact with product at ambient temperatures, remove contaminated shoes and clothing.
Wipe off excess material. Wash exposed skin with mild soap and water. Seek medicalattention if tissue appears damaged or if pain or irritation persists. Thoroughly cleancontaminated clothing before reuse. Discard contaminated leather goods. If material isinjected under the skin, seek medical attention immediately.
Ingestion
Do not induce vomiting unless directed to by a physician. Rinse out mouth with water. Nevergive anything by mouth to a person who is not fully conscious. Allow small quantities to passthrough the digestive system. If large amounts are swallowed or irritation or discomfortoccurs, seek medical attention immediately.
Notes to Physician
SKIN: In the event of injection in underlying tissue, immediate treatment should includeextensive incision, debridement and saline irrigation. Inadequate treatment can result inischemia and gangrene. Early symptoms may be minimal.
INGESTION: Check for possible bowel obstruction with ingestion of large quantities ofmaterial.
SECTION 5. FIRE FIGHTING MEASURES
NFPA Flammability
NFPA Class-IIIB combustible material.
Classification
Flash Point
Open cup: 218°C (424°F) (Cleveland. (Minimum)).
Lower Flammable Limit
Upper Flammable Limit
Autoignition
Temperature
Hazardous Combustion Carbon dioxide, carbon monoxide, smoke, fumes, unburned hydrocarbons and trace oxides
Products
of sulfur, phosphorus, zinc and/or nitrogen.
Special Properties
Fight the fire from a safe distance in a protected location. Open any masses with a waterstream to prevent reignition due to smoldering. Cool surface with water fog. Molten materialcan form flaming droplets if ignited. Water or foam can cause frothing. Use of water onproduct above 100o C (212o F) can cause product to expand with explosive force. Do notallow liquid runoff to enter sewers or public waters.
Extinguishing Media
Use dry chemical, foam, Carbon Dioxide or water fog.
Protection of Fire
Firefighters must use full bunker gear including NIOSH-approved positive pressure Fighters
self-contained breathing apparatus to protect against potential hazardous combustion ordecomposition products and oxygen deficiencies.
SECTION 6. ACCIDENTAL RELEASE MEASURES
Take proper precautions to ensure your own health and safety before attempting spill control or clean-up. For
more specific information, refer to the Emergency Overview on Page 1, Exposure Controls and Personal
Protection in Section 8 and Disposal Considerations in Section 13 of this MSDS.

OMNI Nuvo Lithium EP No. 2 Grease
Do not touch damaged containers or spilled material unless wearing appropriate protectiveequipment. Slipping hazard; do not walk through spilled material. Stop leak if you can do sowithout risk. For small spills, absorb or cover with dry earth, sand, or other inertnon-combustible absorbent material and place into waste containers for later disposal.
Contain large spills to maximize product recovery or disposal. Prevent entry into waterways orsewers. In urban area, cleanup spill as soon as possible. In natural environments, seekcleanup advice from specialists to minimize physical habitat damage. This material will floaton water. Absorbent pads and similar materials can be used. Comply with all laws andregulations.
SECTION 7. HANDLING AND STORAGE
Handling
If this product is stored or applied in high-pressure systems such as grease guns or hydrauliclines, there is the potential for accidental injection into the skin and underlying tissues.
Hydrocarbons injected into skin or underlying tissues are not readily removed by body fluidsand can cause pain, swelling, chemical irritation, infection and tissue destruction. Earlysymptoms may be minimal. Workers must be aware of the significant hazards associatedwith a hydrocarbon injection injury. In the event of an injection injury, workers should seekmedical treatment immediately. Avoid water contamination and elevated temperatures tominimize product degradation. Empty containers may contain product residues that can ignitewith explosive force. Do not pressurize, cut, weld, braze solder, drill, grind or exposecontainers to flames, sparks, heat or other potential ignition sources. Consult appropriatefederal, state and local authorities before reusing, reconditioning, reclaiming, recycling ordisposing of empty containers and/or waste residues of this product.
Keep container closed. Do not store with strong oxidizing agents. Do not store at elevatedtemperatures. Avoid storing product in direct sunlight for extended periods of time. Consultappropriate federal, state and local authorities before reusing, reconditioning, reclaiming,recycling or disposing of empty containers or waste residues of this product.
SECTION 8. EXPOSURE CONTROLS AND PERSONAL PROTECTION
Engineering Controls
Ventilation controls are not normally required under anticipated conditions of use. Provideexhaust ventilation or other engineering controls if airborne mists or vapors concentrationsexceed recommended occupational exposure limits listed below. An eye wash station andsafety shower should be located near the work-station.
Personal Protective
Personal protective equipment should be selected based upon the conditions under which Equipment
this material is used. A hazard assessment of the work area for PPE requirements shouldbe conducted by a qualified professional pursuant to OSHA regulations. The followingpictograms represent the minimum requirements for personal protective equipment. Forcertain operations, additional PPE may be required.
Eye Protection
Safety glasses equipped with side shields are recommended as minimum protection inindustrial settings. Wear goggles and/or face shield if splashing or spraying is anticipated.
Wear goggles and face shield if material is heated above 125°F (51°C). Have suitable eyewash water available.
Hand Protection
Use gloves constructed of chemical resistant materials such as neoprene or heavy nitrilerubber if frequent or prolonged contact is expected. Use heat-protective gloves whenhandling product at elevated temperatures.
OMNI Nuvo Lithium EP No. 2 Grease
Body Protection
Use clean protective clothing (e.g., neoprene or Tyvek®) if splashing or spraying conditionsare present. Protective clothing may include long-sleeve outer garment, apron, or lab coat.
If significant contact occurs, remove oil-contaminated clothing as soon as possible andpromptly shower. Launder contaminated clothing before reuse or discard. Wear heatprotective boots and protective clothing when handling material at elevated temperatures.
Respiratory Protection
Vaporization is not expected at ambient temperatures. Therefore, the need for respiratoryprotection is not anticipated under normal use conditions and with adequate ventilation. Ifelevated airborne concentrations above applicable workplace exposure levels areanticipated, a NIOSH-approved organic vapor respirator equipped with a dust/mist prefiltershould be used. Protection factors vary depending upon the type of respirator used.
Respirators should be used in accordance with OSHA requirements (29 CFR 1910.134).
General Comments
Use good personal hygiene practices. Wash hands and other exposed skin areas withplenty of mild soap and water before eating, drinking, smoking, use of toilet facilities, orleaving work. DO NOT use gasoline, kerosene, solvents or harsh abrasives as skincleaners. Since specific exposure standards/control limits have not been established for thisproduct, the "Oil Mist, Mineral" exposure limits shown below are suggested as minimumcontrol guidelines.
Occupational Exposure Guidelines
Substance
Applicable Workplace Exposure Levels
ACGIH (United States).
TWA: 5 mg/m3 8 hour(s).
STEL: 10 mg/m3 15 minute(s).
OSHA (United States).
TWA: 5 mg/m3 8 hour(s).
ACGIH TLV (United States).
TWA: 10 mg/m3 8 hour(s).
SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES (TYPICAL)
Physical State
Specific Gravity
Boiling Range
Melting/Freezing
Vapor Pressure
Volatility
Solubility in
Viscosity
(cSt @ 40°C)
Additional
Properties
SECTION 10. STABILITY AND REACTIVITY
Chemical Stability
Hazardous Polymerization
Conditions to Avoid
Keep away from extreme heat, sparks, open flame, and strongly oxidizing conditions.
Materials
Incompatibility
OMNI Nuvo Lithium EP No. 2 Grease
Hazardous
No additional hazardous decomposition products were identified other than the combustion Decomposition
products identified in Section 5 of this MSDS.
Products
SECTION 11. TOXICOLOGICAL INFORMATION
For other health-related information, refer to the Emergency Overview on Page 1 and the Hazards Identification
in Section 3 of this MSDS.

Toxicity Data
Distillates, petroleum, hydrotreated heavy naphthenic:
ORAL (LD50):
Mineral oil mists derived from highly refined oils are reported to have low acute and sub-acutetoxicities in animals. Effects from single and short-term repeated exposures to highconcentrations of mineral oil mists well above applicable workplace exposure levels includelung inflammatory reaction, lipoid granuloma formation and lipoid pneumonia. In acute andsub-acute studies involving exposures to lower concentrations of mineral oil mists at or nearcurrent work place exposure levels produced no significant toxicological effects.
Residual oils, petroleum, solvent-refined:
ORAL (LD50):
Mineral oil mists derived from highly refined oils are reported to have low acute and sub-acutetoxicities in animals. Effects from single and short-term repeated exposures to highconcentrations of mineral oil mists well above applicable workplace exposure levels includelung inflammatory reaction, lipoid granuloma formation and lipoid pneumonia. In acute andsub-acute studies involving exposures to lower concentrations of mineral oil mists at or nearcurrent work place exposure levels produced no significant toxicological effects. In long termstudies (up to two years) no carcinogenic effects have been reported in any animal speciestested.
Distillates, petroleum, hydrotreated light naphthenic:
ORAL (LD50):
INHALATION (LC50) Acute: 9.6 mg/L (Female Rat).
INHALATION (LC50) Acute: 10.5 mg/L (Male Rat).
DRAIZE EYE Acute: Non-irritating (Rabbit).
DRAIZE DERMAL Acute: Mild skin irritant (Rabbit).
BUEHLER DERMAL Acute: Non-sensitizing (Guinea Pig).
28-Day DERMAL Sub-Chronic: Mild to moderate skin irritant (Rabbit & Rat).
A life-time dermal application of severely hydrotreated light naphthenic oils produced skinmasses on mice which correlated with the skin irritation response levels of the test animals.
Additional studies attribute these masses to a weak promotional activity. These studiesindicate that light naphthenic oils are not mutagenic, tumor initiators nor complete chemicalcarcinogens. These materials have not been determined to be carcinogenic by IARC, NTP orOSHA.
Grease:
Injection of pressurized hydrocarbons under the skin, in muscle or into the blood stream can
cause irritation, inflammation, swelling, fever and mild central nervous system depression.
Injection of pressurized hydrocarbons can cause severe, permanent tissue damage.
OMNI Nuvo Lithium EP No. 2 Grease
SECTION 12. ECOLOGICAL INFORMATION
Ecotoxicity
Ecotoxicity data are not available for this product.
Environmental Fate
An environmental fate analysis is not available for this specific product. Plants and animalsmay experience harmful or fatal effects when coated with petroleum-based products.
Petroleum-based (mineral) lube oils will normally float on water. In stagnant or slow-flowingwaterways, an oil layer can cover a large surface area. As a result, this oil layer might limit oreliminate natural atmospheric oxygen transport into the water. With time, if not removed,oxygen depletion in the waterway can result in a loss of marine life or create an anaerobicenvironment. This material contains phosphorus which is a controlled element for disposal ineffluent waters in most sections of North America. Phosphorus is known to enhance theformation of algae. Severe algae growth can reduce oxygen content in the water possiblybelow levels necessary to support marine life.
SECTION 13. DISPOSAL CONSIDERATIONS
Hazard characteristic and regulatory waste stream classification can change with product use. Accordingly, it is
the responsibility of the user to determine the proper storage, transportation, treatment and/or disposal
methodologies for spent materials and residues at the time of disposition.

Conditions of use may cause this material to become a "hazardous waste", as defined byfederal or state regulations. It is the responsibility of the user to determine if the material is a"hazardous waste" at the time of disposal. Transportation, treatment, storage, and disposalof waste material must be conducted in accordance with RCRA regulations (see 40 CFR 260through 40 CFR 271). State and/or local regulations may be more restrictive. Contact theRCRA/Superfund Hotline at (800) 424-9346 or your regional US EPA office for guidanceconcerning case specific disposal issues. Empty drums and pails retain residue. DO NOTpressurize, cut, weld, braze, solder, drill, grind, or expose this product's empty container toheat, flame, or other ignition sources. DO NOT attempt to clean it. Empty drums and pailsshould be drained completely, properly bunged or sealed, and promptly sent to areconditioner.
SECTION 14. TRANSPORT INFORMATION
The shipping description below may not represent requirements for all modes of transportation, shipping
methods or locations outside of the United States.

US DOT Status
Not regulated by the U.S. Department of Transportation as a hazardous material.
Proper Shipping Name
Hazard Class
Packing Group(s)
UN/NA Number
Reportable Quantity
A Reportable Quantity (RQ) has not been established for this material.
Placard(s)
Emergency Response
Guide No.
HAZMAT STCC No.
MARPOL III Status
Not a DOT "MarinePollutant" per 49 CFR171.8.
OMNI Nuvo Lithium EP No. 2 Grease
SECTION 15. REGULATORY INFORMATION
TSCA Inventory
This product and/or its components are listed on the Toxic Substances Control Act (TSCA)inventory.
SARA 302/304
The Superfund Amendments and Reauthorization Act of 1986 (SARA) Title III requires Emergency Planning
facilities subject to Subparts 302 and 304 to submit emergency planning and notification and Notification
information based on Threshold Planning Quantities (TPQs) and Reportable Quantities(RQs) for "Extremely Hazardous Substances" listed in 40 CFR 302.4 and 40 CFR 355. Nocomponents were identified.
SARA 311/312 Hazard
The Superfund Amendments and Reauthorization Act of 1986 (SARA) Title III requires Identification
facilities subject to this subpart to submit aggregate information on chemicals by "HazardCategory" as defined in 40 CFR 370.2. This material would be classified under the followinghazard categories: No SARA 311/312 hazard categories identified.
SARA 313 Toxic
This product contains the following components in concentrations above de minimis levels Chemical Notification
that are listed as toxic chemicals in 40 CFR Part 372 pursuant to the requirements of Section and Release Reporting
313 of SARA: No components were identified.
The Comprehensive Environmental Response, Compensation, and Liability Act of 1980(CERCLA) requires notification of the National Response Center concerning release ofquantities of "hazardous substances" equal to or greater than the reportable quantities (RQ's)listed in 40 CFR 302.4. As defined by CERCLA, the term "hazardous substance" does notinclude petroleum, including crude oil or any fraction thereof which is not otherwisespecifically designated in 40 CFR 302.4. Chemical substances present in this product orrefinery stream that may be subject to this statute are: Zinc and Zinc Compounds,Concentration: 0 - 1% Clean Water Act
This material is classified as an oil under Section 311 of the Clean Water Act (CWA) and the Oil Pollution Act of 1990 (OPA). Discharges or spills which produce a visible sheen on watersof the United States, their adjoining shorelines, or into conduits leading to surface waters mustbe reported to the EPA's National Response Center at (800) 424-8802.
California
This material may contain the following components which are known to the State of California Proposition 65
to cause cancer, birth defects or other reproductive harm, and may be subject to therequirements of California Proposition 65 (CA Health & Safety Code Section 25249.5):Toluene: 0.0001% New Jersey
Right-to-Know Label
Additional Regulatory
SECTION 16. OTHER INFORMATION
Refer to the top of Page 1 for the HMIS and NFPA Hazard Ratings for this product.
REVISION INFORMATION
Version Number
Revision Date
Print Date
ABBREVIATIONS
AP: Approximately EQ: Equal >: Greater Than <: Less Than NA: Not Applicable ND: No Data NE: Not Established OMNI Nuvo Lithium EP No. 2 Grease
ACGIH: American Conference of Governmental Industrial Hygienists AIHA: American Industrial Hygiene Association IARC: International Agency for Research on Cancer NIOSH: National Institute of Occupational Safety and Health OSHA: Occupational Safety and Health Administration NPCA: National Paint and Coating Manufacturers Association HMIS: Hazardous Materials Information System NFPA: National Fire Protection Association DISCLAIMER OF LIABILITY
THE INFORMATION IN THIS MSDS WAS OBTAINED FROM SOURCES WHICH WE BELIEVE ARE RELIABLE.
HOWEVER, THE INFORMATION IS PROVIDED WITHOUT ANY WARRANTY, EXPRESSED OR IMPLIED
REGARDING ITS CORRECTNESS. SOME INFORMATION PRESENTED AND CONCLUSIONS DRAWN HEREIN ARE
FROM SOURCES OTHER THAN DIRECT TEST DATA ON THE SUBSTANCE ITSELF. THIS MSDS WAS PREPARED
AND IS TO BE USED ONLY FOR THIS PRODUCT. IF THE PRODUCT IS USED AS A COMPONENT IN ANOTHER
PRODUCT, THIS MSDS INFORMATION MAY NOT BE APPLICABLE. USERS SHOULD MAKE THEIR OWN
INVESTIGATIONS TO DETERMINE THE SUITABILITY OF THE INFORMATION OR PRODUCTS FOR THEIR
PARTICULAR PURPOSE.

THE CONDITIONS OR METHODS OF HANDLING, STORAGE, USE, AND DISPOSAL OF THE PRODUCT ARE
BEYOND OUR CONTROL AND MAY BE BEYOND OUR KNOWLEDGE. FOR THIS AND OTHER REASONS, WE DO
NOT ASSUME RESPONSIBILITY AND EXPRESSLY DISCLAIM LIABILITY FOR LOSS, DAMAGE OR EXPENSE
ARISING OUT OF OR IN ANY WAY CONNECTED WITH HANDLING, STORAGE, USE OR DISPOSAL OF THE
PRODUCT.

Source: http://www.pureguard.us/MSDS/Lithium_EP_No_2_Grease_En.pdf

E:\administ\corresp\2004\prive\verslag22.wp8

Sorry mensen, maar het is niet meer volledig in te halen. Vandaar een “beknopte” versie. Op donderdag 3 maart hebben we een avond van de NL-club. Deze keer thuis bij Mw. BettyBausch, zij is samen met haar zus Lies de auteur van het boek ‘Bewogen stilte,oorlogsherinneringen van twee zussen’ waarin zij verhalen over hun oorlogsverleden enreizen naar Israel. Het is een indrukwekkende avond.

ispt.ac.mz

Preâmbulo Tornando-se necessário definir as regras de funcionamento académico-pedagógico do Instituto Superior Politécnico de Tete (ISPT) e, no uso da competência que lhe é conferida pela alínea g) do n° 2 do artigo 11 do Estatuto do ISPT, aprovado pela Resolução n° 24/2010, de 30 de Julho, da Comissão Interministerial da Função Pública, o Director-Geral do 1. É aprovado o

Copyright © 2014 Medical Pdf Articles