Untitled

locations with no electric power
technological processes and laboratories
long term field measurement

Loggers are designed for record of voltage signal 0-5V (optionally 0-
10V) or current signal 0-20mA. Values are stored to a non volatile
electronic memory. Data transfer to the personal computer for
further analysis is performed via serial interface RS232, USB or
Ethernet by means of a proper adapter or GSM modem.

included calibration certificate from the manufacturer variability of connection to the computer - USB, RS232, Ethernet, GSM modemfast data transfer to the PC (full memory for approximately 30s)permanent connection to the PC enabled, data is possible to download even during logginglarge data memory 32000 valueslarge dual line display with special symbols, switchableoptional display of minimum and maximum measured values (reset of min/max memory from PC or by magnet)dual level alarm is enabled for each channel, alarm is indicated by blinking of the value on the LCD displaytwo alarm modes are enabled: instant or with memory (detected alarm is indicated permanently till alarmmemory is cleared)robust watertight case, easy installation, locking enabledlow power consumption, battery life up to 6 years, indication of remaining battery life, easy battery replacementlogging start/stop is enabled: at certain time and date programmed from computer or by delivered magnetalso special logging mode is enabled, when logging runs only, if some of measured values are out of adjustedalarm limitsinput signal is recalculated and displayed in real measured physical units by means of the PC softwareeach channel is possible to describe with text of 16 characters, each logger with text of maximum 32 characterspassword protection enabled to prevent unauthorized manipulation TECHNICAL PARAMETERS
Measurement accuracy:
Resolution of voltage input:
Resolution of current input:
Signal character at binary input:
from potential-less contact or two-state voltage signal Minimum pulse duration at binary input:
500 ms (shorter pulses may not be recorded) Maximum frequency at binary input:
Power current through contact at binary input:
Voltage accross open contact at binary input:
Low voltage level at binary input:
0 to +0.2 V (maximum current from the input 3 uA High voltage level at binary input:
+3.0 to +30 V (maximum current to the input 100 nA Logging interval:
Display refresh and alarm state refresh:
Total memory capacity:
Logging modes:
noncyclic logging stops after filling the memory
cyclic after filling memory oldest data is overwritten by new
Operation temperature range:
Real time clock:
year, leap year, month, day, hour, minute, second Built-in connector for input signals:
Dimensions without connectors:
Weight including battery:
Typical battery life:
Battery life in on-line mode with interval 1min:
Battery life in on-line mode with interval 10s:
Protection:
IP67 - protected against influence of temporary immersion into water DESCRIPTION
Measuring
S5011 Single channel voltage logger
S5021 Dual channel voltage logger.
Input channels are not galvanic isolated and have common ground.
S6011 Single channel current logger. The current loop should be powered
S6021 Dual channel current logger. The current loops should be powered
from external power supply. Input channels are not galvanic isolatedand have common ground.
No accessory is included. For basic use it is necessary to order at minimum a COM adapter or USB adapter for communication with computer, optionally a start/stop magnet, if needed to control logging the other way than directly from computer or by binary signal. Also connector for input signals connection is necessary to order.
INCLUDED ACCESSORIES: Traceable calibration certificate from the manufacturer, instruction manual. Calibration
certificate with declared metrological traceability of etalons is based on requirements of EN ISO/IEC 17025 standard.
Free program for Windows is ready to download from www.cometsystem.cz. Program enables to control all logger functions and viewing and printing of record in numerical and simple graphic format. It is possible to export logged values to dbf or txt OPTIONAL ACCESSORY:
SW100 - CD with free PC program
LP002 - COM adapter
for communication with personal computer via RS232 serial port
LP003 - USB adapter for communication with personal computer via USB port
LP005 - LAN adapter for communication with the PC via Ethernet, including ac/dc adapter 230V
Exceeding of adjusted limits is alarmed by sending e-mail message or trap.
LP004 - start/stop magnet
MD036 - self adhesive Dual Lock
for easy installation
K092 - watertight female connector Canon 9 pins with cover for connection of input signal, protection IP67
K0925 - female connector Canon 9 pins with cover for connection of input signal, no protection (IP20)
K0945 - adapter with terminals for easy connection of input signals, protection IP20
F9000 - wall holder secured against unauthorized removal
A4203 - spare Lithium battery 3.6V, no leads, size AA
SWR004 - optional software for Windows - color print, vertical and time zoom of graphs and other functions
record of pulses from water meter, gas meter, electrometer,
flow meter, revolution counter
time event record from binary signal (e.g. door opening/closing . )
production monitoring
long term field measurement

Logger is designed for counting of pulses, optionally for logging of time
events from binary signal. Counter reading and actual state of binary
input are displayed on dual line LCD display. Counter status is stored in
adjustable time interval into logger´s non-volatile memory. Time of event
(change of binary input state) is stored immediately after event. Data
transfer to the personal computer for further analysis is performed via
serial interface RS232, USB or Ethernet by means of a proper adapter
or GSM modem.

counter reading is possible to display in real value, range of the LCD display is 19999, after exceeding ofdisplayable value only lowest places are displayed with warning symbolcounter has two modes enabled: after counting of maximum value counter stops or overflows and counts again,counter reset enabled from the PCin the record is possible to indicate counter state or counter state increment between logging intervalsrecord from binary input contains date and time (resolution of 1 s) when change of input logic level appearedand its logic staterecord from binary input is possible to disable.
it is possible from the PC to assign both logic states of binary input a description, which is displayed on therecord. On the LCD logic states are always displayed as ON ( contact closed) and OFF (contact opened)variability of connection to the computer - USB, RS232, Ethernet, GSM modempermanent connection to the PC enabled, data is possible to download even during logginglogging start/stop is enabled: at certain time and date programmed from computer, by signal connected tobinary input or by delivered magnetalso special logging mode is enabled, when logging runs only, if counter reading is out of adjusted alarm limitsinput pulse signal is recalculated and displayed in real measured physical units by means of the PC softwareeach channel is possible to describe with text of maximum 16 characters, each logger with text of 32 characterspassword protection enabled to prevent unauthorized manipulationextremely low consumption from the battery, indication of remaining battery life, easy battery replacementrobust watertight case, easy installation, locking enabled TECHNICAL PARAMETERS
Counter range user selectable:
in 16bit mode: 0 to 61 695 pulses, memory of 32 504 records in non-cyclic mode in 32bit mode: 0 to 2 021 654 527 pulses, memory of 16 252 records in non-cyclic mode Input signals:
from potential-less contact or two state voltage signal Parameters of counting input:
minimum pulse duration: 1 ms (shorter pulses may not be recorded) current through closed contact: 30uA, maximum voltage across opened contact: 3.6V LOW voltage level: 0 to +0.2V (current from input max 30uA) HIGH voltage level: +3.0 to +30V (current to input max 100nA) Parameters of binary input:
minimum pulse duration: 500 ms (shorter pulses may not be recorded) maximum frequency: 0.5Hz (i.e. maximum 5 pulses in 10s) current through closed contact: 3uA, maximum voltage across opened contact: 3.6V LOW voltage level: 0 to +0.2V (current from input max 3uA) HIGH voltage level: +3.0 to +30V (current to input max 100nA) Operational temperature range:
Real time clock:
year, leap year, month, day, hour, minute, second Logging interval of counting input:
Refresh of display and alarm state:
Logging modes:
noncyclic logging stops after filling the memory
cyclic after filling memory oldest data is overwritten by new
Built-in connector for input signals:
Dimensions without connector,
Lithium battery 3,6V, size AA, typical life 3 years, indication of remaining life Protection:
IP67- protected against influence of temporary immersion into water Logger includes no accessories. For basic use it is necessary to order at minimum a COM adapter or USB adapterfor communication with computer, optionally a start/stop magnet, if needed to control logging the other way thandirectly from computer or external binary signal. Also connector for input signals connection is necessary to order.
INCLUDED ACCESSORIES: battery, free program for Windows is ready to download from www.cometsystem.cz.
Program enables to control all logger functions and viewing and printing of record in numerical and simple graphic
format. It is possible to export logged values to dbf or txt formats for further analysis.
OPTIONAL ACCESSORY:
SW100 - CD with free PC program
LP002 - COM adapter for communication with personal computer via RS232 serial port
LP003 - USB adapter for communication with personal computer via USB port
LP005 - LAN adapter for communication with the PC via Ethernet, including ac/dc adapter 230V
Exceeding of adjusted limits is alarmed by sending e-mail message or trap.
LP004 - start/stop magnet
MD036 - self adhesive Dual Lock for easy installation
K0921 - watertight female connector Canon 9 pins with cover for connection of input signal, protection IP67
K0925 - female connector Canon 9 pins with cover for connection of input signal, no protection (IP20)
K0945 - adapter with terminals for easy connection of input signals, protection IP20
F9000 - wall holder secured against unauthorized removal
A4203 - spare Lithium battery 3.6V, size AA, no leads
SWR004 - optional software for Windows color print, vertical and time zooming of graphs and other functions
Datalogger T-PRINT is designed for logging temperature
from one external probe into its internal memory. Datalogger
T-PRINT-2 logs temperature from two external probes.
Anytime it is possible to print out the record on the built in
needle printer. The result is a hardcopy on the strip of paper
of 58mm width. Format is numerical with date, time, place of
measurement (vehicle, cold store). It is possible to repeat
the print out from the last stored temperature to the past
until a button is pressed to stop printing. Consequently it is
easily possible to print out a hardcopy of transport conditions
to every client.
It is also possible to transfer logged data into a PC. Then it ispossible to analyze and print out temperature in numericaland graphic format. The PC software enables to erasedatalogger memory, set logging interval, set internal realtime clock. It also enables to enter the place of measurement(vehicle) to printout heading. After datalogger memory is full,datalogging continues and the oldest stored values arecyclically being replaced by the Newest.
The T-PRINT datalogger memory is fulfilled in 40 days of continuous record with logging interval of 5 minute or4 months with 15 minutes sampling interval. Memory fulfilling times of dual channel datalogger T-PRINT-2 are20 days/5minute interval and 2 months/15 minute interval.
TECHNICAL PARAMETERS
Operating temperature range of the printer: 9 to 32V dc, protected against alternator load shedding+ internal lithium battery 3.6V, 5 years of minimum life - internal clock back-up Tested by accredited laboratory in accordance with the European Standard EN12830 -
Temperature recorders for the transport, storage and distribution of chilled and frozen
food.

It is necessary to order temperature probe with the Ni1000/6180ppm sensor. Recommended is the multi-purposewatertight probe N1ATG8U/C on the PVC cable with Cinch connector. Range of the probe -30 to +80°C. Pleasespecify required cable length 5, 10 or 15 meters.
Warranty: two years
Datalogger is designed for installation at driver`s cabin. Connected
temperature probes are located in chilled or frozen space. Anytime it is possible to print out the record. Low cost operation is the advantage.
Needle printer requires only usual paper in 58mm rolls of 30 meters length. One roll of the paper enables to print out 9000 lines of record. Life of ribbon cassette enables to print out 3 rolls of paper.
T1(°C): FROZEN SECTIONT2(°C): CHILLED SECTION Included accessory: Traceable calibration certificate from the
manufacturer, instruction manual. Calibration certificate with declared metrological traceability of etalons is based on requirements of EN ISO/IEC 17025 standard. Included is also PC cable, internal Lithium battery 3.6V for supplying the internal clock, ribbon cassette, roll ofpaper, self adhesive Dual Lock for easy installation. Free Windowsprogram is ready to download at www.cometsystem.czProgram enables to control all logger functions and viewing and printing ofdata in numerical and simple graphic formats. It is possible to export datato dbf or txt formats.
Optional accessory:
SW100
- CD with free PC program
probes with Ni1000/6180 RTD sensor with Cinch connector
- probe marking followed by letter /C
MP006 - RS232/USB converter for communication with the PC via USB port
A1536 - mains ac/dc adapter 230V-50Hz/12V-500mA
A4203 - spare Lithium battery 3.6V
PR002 - spare roll of paper for printer, width 58mm,
length 30m 9000lines of record
DPN-290BL - spare ribbon cassette for printer,
life 3 printed out rolls of paper
SWR004 - optional software for Windows
color print, vertical and time zooming of graphs and other functions Warranty: two years

Source: http://www.humisystem.co.kr/humi/pdf/7_12.pdf

biolt.co.jp

Clin Exp Immunol 1997; 110 :500–508 Circadian rhythm of leucocytes and lymphocyte subsets and its possible correlation with the function of the autonomic nervous system S. SUZUKI*†, S. TOYABE*, T. MORODA†, T. TADA†, A. TSUKAHARA†, T. IIAI†, M. MINAGAWA†,S. MARUYAMA†, K. HATAKEYAMA†, K. ENDOH‡ & T. ABO* * Department of Immunology, † First Department of Surgery,

denka.co.jp

DENKA to strengthen Capital Alliance with SEI Corporation in the Field of Lithium-ion Secondary Battery Technology DENKA (president: Shinsuke Yoshitaka) and SEI Corporation (headquarters: Tsu, Mie; representative director: Takehiko Sawai; hereafter “SEI”) have reached an agreement to accelerate the development of electrode material technologies, with a focus on high conductivity (lo

Copyright © 2014 Medical Pdf Articles